№ | Name | Ext. inf. | A* | Use of | Part number |
---|---|---|---|---|---|
wiring set for engine
petr. engine
|
petr. engine | ||||
wiring set for engine
PR-TV0
|
PR-TV0 | ||||
1 | wiring set for engine | 1 | 03H 971 627 F | ||
individual parts
PR-TV0
|
PR-TV0 | ||||
- | * corrug. tubes, t-pieces, * clips, holders, grommets, * cable ties, insulating * hose, wiring, * single wires and seals * see special catalogue: * electrical * connecting elements |
||||
2 | flat contact housing with contact locking mechanism control unit use if required: 7L0 971 904 7L0 971 904 A |
7L0 971 904 7L0 971 904 A |
1 X X |
5Q0 906 379 A | |
- | sealing pin 1,5 MM
|
1,5 MM | X | 7L0 971 904 | |
- | sealing pin 0,63 MM
|
0,63 MM | X | 7L0 971 904 A | |
3 | cable guide injection valve |
1 | 03H 971 824 L | ||
6 | bracket protective cover | 3 | 022 971 921 | ||
7 | bracket protective cover | 3 | 022 971 921 A | ||
8 | flat connector housing with contact locking mechanism injection valve |
X 6 |
4D0 971 992 | ||
9 | flat connector housing with contact locking mechanism fuel pump |
1 | 4D0 971 992 A | ||
10 | flat connector housing with contact locking mechanism pressure sensor |
1 | 4D0 971 993 | ||
11 | flat contact housing with contact locking mechanism oil pressure switch |
1 | 1J0 973 081 | ||
12 | flat contact housing with contact locking mechanism throttle valve control element |
1 | 4H0 973 713 | ||
13 | flat contact housing with contact locking mechanism camshaft adjuster unit knock sensor |
X 2 1 |
8K0 973 702 | ||
14 | flat contact housing with contact locking mechanism additional coolant pump temperature sensor |
X 1 1 |
8K0 973 702 | ||
15 | flat contact housing with contact locking mechanism low-pressure sensor impulse sender camshaft |
X 1 2 |
8K0 973 703 | ||
16 | flat contact housing with contact locking mechanism knock sensor |
1 | 8K0 973 703 F | ||
17 | flat contact housing with contact locking mechanism vent hose |
1 | 1J0 973 722 A | ||
18 | flat contact housing with contact locking mechanism activated charcoal container with valve |
1 | 6X0 973 722 G | ||
19 | flat contact housing with gasket impulse sender crankshaft |
1 | 1J0 973 723 | ||
20 | flat contact housing with contact locking mechanism ignition coil |
6 | 4B0 973 724 | ||
21 | flat contact housing with contact locking mechanism central wiring set |
1 | 5Q0 973 837 | ||
22 | cable tie with terminal socket for bridge strength: (clamp base, rotating) 4,6X200MM
1-3MM |
4,6X200MM 1-3MM |
1 | 3D0 971 838 M | |
23 | cable ties toothed quadrant hole/sheet metal thickness: 4,5X200MM
6,5/0,3-3,0MM |
4,5X200MM 6,5/0,3-3,0MM |
X | 3W0 971 838 | |
(23) | cable holder hole/sheet metal thickness: 6,5/0,6-3,0MM |
6,5/0,6-3,0MM |
X | 4B0 971 848 | |
24 | holder for wiring harness | X | N 104 828 01 | ||
25 | bracket 15X13MM
|
15X13MM | X | N 105 023 01 | |
26 | cable ties toothed quadrant 4,6X193MM
|
4,6X193MM | 1 | N 909 377 02 | |
27 | bracket for corrugated pipe | 1 | N 906 981 01 | ||
(27) | cable holder | 1 | 03L 971 845 G | ||
single parts whitch are not included with the parts supp- lied with the wiring harness PR-TV0
|
PR-TV0 | ||||
30 | cable holder gearbox |
1 | 1H0 971 615 AB | ||
31 | cable guide - upper part counterpart to: 03H 971 824 L |
03H 971 824 L |
1 | 03H 971 797 | |
32 | holder for wiring harness oil level sensor use if required: N 906 813 01 |
N 906 813 01 |
1 | 1K0 971 842 H | |
33 | retaining bracket gearbox |
1 | 1K0 971 858 AS | ||
34 | retaining clip area: lambda probe |
1 | 1J0 971 939 K | ||
35 | hexagon collar nut M6
|
M6 | 2 | N 015 082 10 | |
36 | insulating hose temp. resistant: 17-19X1000MM
-40C/+150C |
17-19X1000MM -40C/+150C |
X | N 107 676 01 |