| №- | Name | A* | Part number |
|---|---|---|---|
| 005 | WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 Replaced by: A 202 350 94 08 |
- | A 202 350 56 08 |
| 005 | WHEEL BEARING WITH LOWER CONTROL ARM JOINT AND WHEEL MOUNTING,LEFT USED WITHOUT SECOND ALTERNATOR |
001 | A 202 350 94 08 |
| 005 | WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 Replaced by: A 202 350 95 08 |
- | A 202 350 57 08 |
| 005 | WHEEL BEARING WITH LOWER CONTROL ARM JOINT AND WHEEL MOUNTING,RIGHT USED WITHOUT SECOND ALTERNATOR |
001 | A 202 350 95 08 |
| 008 | JOINT Replaced by: A 220 352 02 27 |
- | A 201 352 00 27 |
| 008 | SUPPORTING JOINT | 002 | A 220 352 02 27 |
| 009 | SEAL RING TO ASCERTAIN THE REAR SPRINGS,PLEASE ADD UP IN THE CHART BELOW THE NUMBERS OF POINTS OF THE RESPECTIVE MODEL AND OF THE SPECIAL VERSIONS INSTALLED ============================================================================================================================== MODEL POINTS CODE SPECIAL EQUIPMENT POINTS 124.027 65 550 HITCHING MECHANISM 6 124.127 63 307 COOL BOX 6 412,414 SLIDING ROOF 3 274,325 AUTOMOBILE TELEPHON 3 211 AUTO. LIMITED-SLIP DIFFERENTIAL 3 420,425 AUTOMATIC TRANSMISSION 1 430 REAR SEAT BENCH HEADRESTS 1 934 TAXI DISTRESS ALARM SYSTEM 1 ============================================================================================================================== CHART OF REAR SPRING RUBBER PADS W/SELF LEVELLING DEVICE CODE 480 ============================================================================================================================== TOTAL OF POINTS REAR SPRING PAD PAD REAR SPRING BLUE REAR SPRING RED -70 124 324 21 04 201 325 09 44 201 325 10 44 71-78 124 324 21 04 201 325 10 44 201 325 11 44 78- 124 324 21 04 201 325 11 44 ============================================================================================================================== USED WITHOUT SLIDING ROOF 1 X 124 620 70 14 |
002 | A 124 997 12 40 |
| 011 | FLANGE | 002 | A 124 350 07 46 |
| 014 | CYLINDER PIN | 002 | A 201 997 00 10 |
| 017 | REPAIR KIT Replaced by: A 202 980 00 16 |
- | A 202 980 01 16 |
| 017 | REPAIR KIT REAR WHEEL BEARING |
002 | A 202 980 00 16 |
| 020 | LOCK | 002 | A 201 994 16 41 |
| 023 | CONTROL ARM SPRING CONTROL ARM |
002 | A 202 350 02 06 |
| 024 | RUBBER MOUNTING | 002 | A 202 352 01 65 |
| 026 | REPAIR KIT MOUNTING PARTS |
002 | A 124 350 67 06 |
| 029 | SCREW SPRING CONTROL ARM TO WHEEL BEARING IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 990 05 04 |
| 032 | HEXAGON NUT SPRING CONTROL ARM TO WHEEL BEARING IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 014001 |
| 035 | HEXAGON HEAD BOLT SPRING CONTROL ARM TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 308765 012023 |
| 038 | WASHER Replaced by: A 124 352 02 76 |
- | A 124 352 00 76 |
| 038 | WASHER SPRING CONTROL ARM TO REAR SUBFRAME |
002 | A 124 352 02 76 |
| 041 | WASHER Replaced by: A 210 357 02 75 |
- | A 201 357 02 75 |
| 041 | WASHER SPRING CONTROL ARM TO REAR SUBFRAME |
002 | A 210 357 02 75 |
| 044 | HEXAGON NUT SPRING CONTROL ARM TO REAR SUBFRAME |
002 | N 910113 012003 |
| 047 | COVERING Replaced by: A 203 352 00 88 |
- | A 129 352 01 88 |
| 047 | COVERING SPRING CONTROL ARM |
002 | A 203 352 00 88 |
| 050 | SCREW PROTECTIVE PLATE TO SPRING CONTROL ARM |
004 | A 210 990 03 36 |
| 056 | CAMBER STRUT UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 Replaced by: A 210 350 34 06 |
- | A 210 350 25 06 |
| 056 | CAMBER STRUT LEFT AND RIGHT USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 34 06 |
| 059 | REPAIR KIT MOUNTING PARTS UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 |
002 | A 124 350 65 06 |
| 059 | REPAIR KIT MOUNTING PARTS USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 45 06 |
| 060 | CLAMPING SLEEVE USED WITHOUT SECOND ALTERNATOR |
002 | A 210 352 00 43 |
| 062 | SCREW CAMBER STRUTS TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 990 11 01 |
| 062 | SCREW CAMBER STRUTS TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 002 990 28 12 |
| 065 | WASHER CAMBER STRUTS TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 357 04 75 |
| 065 | WASHER CAMBER STRUTS TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 210 357 06 75 |
| 068 | WASHER CAMBER STRUTS TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 |
002 | N 000125 010532 |
| 068 | WASHER CAMBER STRUTS TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | N 000433 013010 |
| 071 | HEXAGON NUT CAMBER STRUTS TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 010000 |
| 071 | HEXAGON NUT CAMBER STRUTS TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | N 910113 012003 |
| 074 | SCREW CAMBER STRUTS TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 009 990 20 01 |
| 077 | HEXAGON NUT CAMBER STRUTS TO REAR SUBFRAME |
002 | N 910113 012003 |
| 080 | STRUT UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 Replaced by: A 210 350 33 06 |
- | A 201 350 56 06 |
| 080 | STRUT USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 33 06 |
| 083 | REPAIR KIT MOUNTING PARTS UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 |
002 | A 124 350 68 06 |
| 083 | REPAIR KIT MOUNTING PARTS USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 45 06 |
| 084 | CLAMPING SLEEVE USED WITHOUT SECOND ALTERNATOR |
002 | A 210 352 00 43 |
| 086 | SCREW STRUT TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 352 03 71 |
| 086 | SCREW STRUT TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 002 990 28 12 |
| 089 | WASHER STRUT TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 357 01 75 |
| 089 | WASHER STRUT TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 210 357 06 75 |
| 092 | WASHER STRUT TO WHEEL BEARING |
002 | N 000433 013010 |
| 095 | HEXAGON NUT STRUT TO WHEEL BEARING IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 012003 |
| 098 | SCREW STRUT TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 009 990 20 01 |
| 101 | HEXAGON NUT STRUT TO REAR SUBFRAME |
002 | N 910113 012003 |
| 104 | TIE ROD PARTS KIT |
002 | A 210 350 21 53 |
| 107 | RUBBER MOUNTING | 002 | A 201 352 88 65 |
| 107 | RUBBER MOUNTING REPAIR SIZE; WITH ECCENTRIC INTERIOR BUSHING |
002 | A 124 352 43 65 |
| 110 | HEXAGON NUT TIE ROD TO WHEEL BEARING M10X1 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 010002 |
| 110 | HEXAGON NUT TIE ROD TO WHEEL BEARING M 10 |
002 | N 910113 010000 |
| 113 | REPAIR KIT TIE ROD TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 140 350 11 70 |
| 116 | HEXAGON NUT TIE ROD TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 012002 |
| 119 | THRUST ARM UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 Replaced by: A 210 350 38 06 |
- | A 210 350 00 29 |
| 119 | THRUST ARM USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 38 06 |
| 122 | REPAIR KIT MOUNTING PARTS UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 |
002 | A 124 350 65 06 |
| 122 | REPAIR KIT MOUNTING PARTS USED WITHOUT SECOND ALTERNATOR |
002 | A 210 350 45 06 |
| 123 | CLAMPING SLEEVE USED WITHOUT SECOND ALTERNATOR |
002 | A 210 352 00 43 |
| 125 | SCREW THRUST ARM TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 990 11 01 |
| 125 | SCREW THRUST ARM TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 002 990 28 12 |
| 128 | WASHER THRUST ARM TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 210 357 04 75 |
| 128 | WASHER THRUST ARM TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | A 210 357 06 75 |
| 131 | WASHER THRUST ARM TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 |
002 | N 000125 010532 |
| 131 | WASHER THRUST ARM TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | N 000433 013010 |
| 134 | HEXAGON NUT THRUST ARM TO WHEEL BEARING UP UNTIL BOLTED CONNECTIONS ON WHEEL CARRIER,THRUST ARM,CAMBER ARM AND RADIUS ROD WERE STANDARDIZED FROM M10 TO M12 IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | N 910113 010000 |
| 134 | HEXAGON NUT THRUST ARM TO WHEEL BEARING USED WITHOUT SECOND ALTERNATOR |
002 | N 910113 012003 |
| 137 | SCREW THRUST ARM TO REAR SUBFRAME IN CASE OF TRAILED LOAD EXCEEDING 1500KG IN TOTAL WEIGHT, TRANSMISSION OIL COOLER WITH ADDITIONAL FAN IS TO BE INSTALLED (SEE B 587816 EXCEPT ALSO INSTALLED IN SPECIAL APPOINTMENTS, VOLUME 3, INSTALLATION INSTRUCTION 27.1) |
002 | A 009 990 20 01 |
| 140 | HEXAGON NUT THRUST ARM TO REAR SUBFRAME |
002 | N 910113 012003 |
| 143 | COVERING THRUST ARM |
002 | A 201 352 09 88 |
Copyright © 2024 WebAutoCat.com. All rights reserved. Terms of Use | Privacy Policy