| №- | Name | A* | Part number |
|---|---|---|---|
| ENGINE LESS STARTING MOTOR,ALTERNATOR,OIL BATH AIR CLEANER,FAN,FAN DRIVE,V-BELT TIGHTENER AND V-BELT DELIVER ADDITIONALY: 1 X 121 155 02 72, 1 X 121 155 00 71, 1 X 000127 014201, 1 X 900071 010202 |
001 | A 180 010 82 45 | |
| SHORT-BLOCK | 001 | A 180 010 24 50 | |
| GASKET KIT ENGINE NO LONGER AVAILABLE,INSTEAD:CYLINDER CRANKASE AND CYLINDER HEAD GASKET KIT |
- | A 180 586 41 90 | |
| 005 | CRANKCASE | 001 | A 180 010 34 08 |
| 007 | SCREW | 001 | N 000933 010111 |
| 009 | SEALING RING Replaced by: N 007603 010110 |
- | N 007603 010103 |
| 009 | SEALING RING | 001 | N 007603 010110 |
| 011 | CRANKSHAFT BEARING CAP CRANKSHAFT BEARINGS NOS. 1, 3, AND 4 |
003 | A 108 011 02 11 |
| 014 | CRANKSHAFT BEARING CAP LAPPED BEARING |
001 | A 108 011 01 13 |
| 017 | SCREW | 008 | N 000931 012061 |
| 019 | WASHER | 008 | A 121 990 28 40 |
| 023 | CYLINDER PIN | 004 | N 000007 010102 |
| 026 | CYLINDER PIN | 004 | N 000007 008101 |
| 030 | BRACKET OIL PUMP SUCTION PIPE |
001 | A 180 186 02 40 |
| 034 | DOWEL PIN INTERMEDIATE PLATE |
001 | A 180 991 03 62 |
| 037 | DOWEL PIN | 001 | A 180 991 04 62 |
| 041 | PIN FABRIC SEAL RING |
001 | A 186 991 00 55 |
| 045 | SCREW NO LONGER AVAILABLE |
003 | A 000 990 47 12 |
| 045 | SCREW NO LONGER AVAILABLE |
002 | A 000 990 47 12 |
| 048 | STUD BOLT | 002 | N 000939 008072 |
| 052 | CYLINDER SIDE COVER STARTING MOTOR SIDE |
002 | A 180 015 08 05 |
| 055 | GASKET Replaced by: A 110 015 01 21 |
- | A 180 015 10 21 |
| 055 | GASKET | 002 | A 110 015 01 21 |
| 057 | SCREW-AND-WASHER ASSEMBLY Replaced by: N 000000 000009 |
- | N 914020 006009 |
| 057 | SCREW-AND-WASHER ASSEMBLY M6X12 |
012 | N 000000 000009 |
| 066 | BEARING INTERMEDIATE GEAR SHAFT, REAR |
001 | A 110 052 01 06 |
| 068 | BEARING HOUSING IGNITION DISTRIBUTOR AND OIL PUMP DRIVE |
001 | A 180 150 01 07 |
| 069 | GASKET KIT Replaced by: A 180 010 08 06 |
- | A 180 010 10 80 |
| 069 | CRANKCASE CYLINDER CRANKCASE |
001 | A 180 010 08 06 |
| 070 | FITTED PIN CYLINDER HEAD |
002 | N 900037 010100 |
| 072 | COVER | 001 | A 180 010 01 35 |
| 074 | CYLINDER PIN | 001 | N 000007 006207 |
| 076 | GASKET | 001 | A 180 011 03 79 |
| 080 | SCREW | 004 | N 000912 006044 |
| 082 | SPRING WASHER | 004 | N 000137 006204 |
| 087 | SHIM | 001 | A 180 011 14 05 |
| 091 | HEXAGON HEAD BOLT | 003 | N 304017 010027 |
| OIL PAN | 001 | A 130 010 12 13 | |
| 096 | THREADED INSERT | 004 | N 900421 012006 |
| 098 | PIN | 001 | A 186 991 00 55 |
| 101 | SEALING RING | 001 | N 007603 022102 |
| 103 | SCREW PLUG Replaced by: N 000908 022011 |
- | N 000908 022001 |
| 103 | SCREW PLUG | 001 | N 000908 022011 |
| 119 | SCREW PLUG OIL DRAIN |
001 | A 136 997 12 30 |
| 121 | SEALING RING OIL DRAIN |
001 | N 915035 000025 |
| 125 | SCREW-AND-WASHER ASSEMBLY OIL PAN TO CYLINDER CRANKCASE |
020 | N 914020 006000 |
| 128 | SCREW OIL PAN TO CYLINDER CRANKCASE |
002 | N 000912 008066 |
| 128 | SCREW OIL PAN TO CYLINDER CRANKCASE |
002 | N 000912 006047 |
| 130 | WASHER OIL PAN TO CYLINDER CRANKCASE |
002 | N 000433 006400 |
| 134 | CAP BOLT Replaced by: N 000000 000190 |
- | N 000912 008111 |
| 134 | CAP BOLT OIL PAN TO CYLINDER CRANKCASE M8X25 |
003 | N 000000 000190 |
| 136 | WASHER OIL PAN TO CYLINDER CRANKCASE |
005 | N 000433 008406 |
| 145 | CYLINDER HEAD Replaced by: A 180 010 00 21 |
- | A 180 010 59 21 |
| 145 | CYLINDER HEAD | 001 | A 180 010 00 21 |
| 146 | SCREW PLUG EXHAUST STOCK OF OLD PARTS UP TO ENGINE: 000105 |
003 | A 180 997 06 30 |
| 148 | SCREW PLUG |
003 | N 000908 022010 |
| 150 | SEALING RING |
003 | N 007603 022102 |
| 153 | VALVE SEAT RING STANDARD,INTAKE |
006 | A 180 053 07 31 |
| 153 | VALVE SEAT RING REPAIR SIZE; INTAKE |
006 | A 180 053 08 31 |
| 157 | VALVE SEAT RING STANDARD,EXHAUST |
006 | A 180 053 07 32 |
| 157 | VALVE SEAT RING REPAIR SIZE; EXHAUST |
006 | A 180 053 08 32 |
| 161 | WATER DISTRIBUTOR | 003 | A 127 016 06 60 |
| 164 | WATER DISTRIBUTOR | 005 | A 127 016 03 60 |
| 167 | WATER DISTRIBUTOR | 001 | A 127 016 04 60 |
| 170 | WATER DISTRIBUTOR | 001 | A 127 016 05 60 |
| 174 | CYLINDER PIN CAMSHAFT BEARINGS |
008 | N 000007 008202 |
| 178 | STUD BOLT CAMSHAFT BEARINGS |
004 | N 000939 008006 |
| 183 | SCREW COOLING WATER OUTLET |
002 | N 000939 008045 |
| 185 | SCREW INTAKE AND EXHAUST MANIFOLDS |
006 | N 000835 010112 |
| 187 | SCREW EXHAUST MANIFOLD |
002 | N 000835 010067 |
| 189 | SCREW CHAIN TIGHTENER HOUSING |
001 | N 000939 008083 |
| CONNECTION PIPE SOCKET HEAT SENSOR |
001 | A 130 016 00 29 | |
| 196 | SEALING RING | 001 | N 007603 030100 |
| 200 | VALVE GUIDE Replaced by: A 180 050 03 24 |
- | A 180 050 02 24 |
| 200 | VALVE GUIDE INTAKE NO LONGER AVAILABLE,INSTAED 180 050 03 24 14.007-14.013 MM,14.013-14.019 MM,14.019-14.025 MM |
- | A 180 050 03 24 |
| 200 | VALVE GUIDE INTAKE ONLY USED WITH 416.81 CAB,OPEN |
006 | A 180 050 03 24 |
| 200 | VALVE GUIDE INTAKE,REPAIR SIZE 14.200 MM |
006 | A 180 050 04 24 |
| 200 | VALVE GUIDE INTAKE,REPAIR SIZE 14.400 |
006 | A 180 050 05 24 |
| 203 | SNAP RING INTAKE |
006 | N 009045 014000 |
| 206 | VALVE GUIDE Replaced by: A 121 050 21 24 |
- | A 121 050 16 24 |
| 206 | VALVE GUIDE EXHAUST NO LONGER AVAILABLE,INSTAED 121 050 21 24 14.007-14.013 MM,14.013-14.019 MM,14.019-14.025 MM |
- | A 121 050 21 24 |
| 206 | VALVE GUIDE EXHAUST ONLY USED WITH 416.81 CAB,OPEN |
006 | A 121 050 21 24 |
| 206 | VALVE GUIDE EXHAUST,REPAIR SIZE 14.200 |
006 | A 121 050 22 24 |
| 206 | VALVE GUIDE EXHAUST,REPAIR SIZE 14.400 MM |
006 | A 121 050 23 24 |
| 210 | SNAP RING EXHAUST |
006 | N 009045 014000 |
| GASKET KIT Replaced by: A 180 010 64 21 |
- | A 180 010 01 80 | |
| GASKET KIT CYLINDER HEAD |
001 | A 180 010 64 21 | |
| 215 | REPAIR KIT STANDARD |
001 | A 130 586 00 05 |
| 215 | REPAIR KIT INTERMEDIATE SIZE |
001 | A 130 586 01 05 |
| 215 | REPAIR KIT REPAIR SIZE I |
001 | A 130 586 02 05 |
| 219 | WASHER CAMSHAFT BEARING TO CYLINDER HEAD |
004 | N 000433 008406 |
| 221 | HEXAGON NUT CAMSHAFT BEARING TO CYLINDER HEAD |
004 | N 304032 008006 |
| 225 | SCREW PLUG | 001 | A 836 997 00 30 |
| 228 | SEALING RING | 001 | N 007603 032103 |
| 232 | CYLINDER HEAD GASKET Replaced by: A 180 016 47 20 |
- | A 180 016 35 20 |
| 232 | CYLINDER HEAD GASKET | 001 | A 180 016 47 20 |
| 234 | CAP BOLT CYLINDER HEAD TO CYLINDER CRANKCASE |
002 | N 000912 008008 |
| 236 | WASHER CYLINDER HEAD TO CYLINDER CRANKCASE |
001 | N 000433 008406 |
| 236 | WASHER CYLINDER HEAD TO CYLINDER CRANKCASE |
002 | N 000433 008406 |
| 240 | CAP BOLT CYLINDER HEAD TO CYLINDER CRANKCASE |
001 | N 000912 008203 |
| 240 | SCREW Replaced by: N 000912 012039 |
- | N 000912 012038 |
| 240 | SCREW CYLINDER HEAD TO CYLINDER CRANKCASE |
008 | N 000912 012039 |
| 242 | WASHER CYLINDER HEAD TO CYLINDER CRANKCASE |
008 | A 110 016 04 76 |
| 245 | BRACKET | 003 | A 115 016 00 38 |
| 249 | SCREW | 006 | N 000912 012031 |
| 251 | WASHER | 006 | A 110 016 04 76 |
| 254 | OIL LINE ONLY USED WITH 406.82 CAB,ENCLOSED |
001 | A 180 180 01 27 |
| 254 | OIL LINE INCLUDED IN RANGE OF DELIVERY OF FUEL PUMP 115 090 00 50 Replaced by: A 130 180 11 27 |
- | A 130 180 02 27 |
| 254 | OIL LINE |
001 | A 130 180 11 27 |
| 256 | SCREW-AND-WASHER ASSEMBLY ONLY USED WITH 406.82 CAB,ENCLOSED |
001 | N 914020 006000 |
| 258 | SCREW INCLUDED IN RANGE OF DELIVERY OF FUEL PUMP 115 090 00 50 |
001 | N 000912 006064 |
| 258 | SCREW-AND-WASHER ASSEMBLY Replaced by: N 000000 000009 |
- | N 914020 006009 |
| 258 | SCREW-AND-WASHER ASSEMBLY M6X12 |
001 | N 000000 000009 |
| 260 | SPRING WASHER ONLY USED WITH 406.82 CAB,ENCLOSED |
001 | N 000137 006204 |
| 260 | SPRING LOCK WASHER INCLUDED IN RANGE OF DELIVERY OF FUEL PUMP 115 090 00 50 |
001 | N 912004 006102 |
| SHIM INCLUDED IN RANGE OF DELIVERY OF FUEL PUMP 115 090 00 50 |
001 | A 130 187 00 84 | |
| 264 | SHIM |
001 | A 115 187 00 84 |
| 266 | CLAMP Replaced by: A 123 995 13 20 |
- | A 121 995 04 20 |
| 266 | CLAMP ONLY USED WITH 406.82 CAB,ENCLOSED |
003 | A 123 995 13 20 |
| 266 | CLAMP |
003 | A 130 995 00 20 |
| 268 | SCREW | 003 | N 000933 004003 |
| 270 | SPRING WASHER | 003 | N 000137 004200 |
| 275 | CYLINDER HEAD COVER ONLY USED WITH 406.82 CAB,ENCLOSED Replaced by: A 180 010 26 30 |
- | A 180 010 19 30 |
| 275 | CYLINDER HEAD COVER |
001 | A 180 010 26 30 |
| 278 | FITTING | 001 | A 615 997 00 72 |
| 280 | SEALING RING | 001 | N 007603 018100 |
| 282 | FILLER CAP ONLY USED WITH 406.82 CAB,ENCLOSED |
001 | A 136 501 00 54 |
| 284 | SEAL RING ONLY USED WITH 406.82 CAB,ENCLOSED Replaced by: A 000 010 12 85 |
001 | A 180 997 02 40 |
| 284 | FILLER CAP ONLY USED WITH 406.82 CAB,ENCLOSED Replaced by: A 000 010 14 85 |
001 | A 000 010 12 85 |
| 284 | FILLER CAP ONLY USED WITH 406.82 CAB,ENCLOSED |
001 | A 000 010 14 85 |
| 286 | CAP THE OLD PART MUST NO LONGER BE INSTALLED Replaced by: A 102 018 04 02 |
- | A 102 018 03 02 |
| 286 | CAP Replaced by: A 102 018 08 02 |
- | A 102 018 04 02 |
| 286 | CAP Replaced by: A 111 018 03 02 |
- | A 102 018 08 02 |
| 286 | FILLER CAP FILLER CAP |
001 | A 111 018 03 02 |
| 288 | GASKET Replaced by: A 102 018 03 80 |
- | A 102 018 00 80 |
| 288 | GASKET 38.5X59 MM; TO 102 018 08 02 |
- | A 102 018 03 80 |
| 288 | GASKET 47.5X59 MM; TO 111 018 03 02 |
001 | A 111 018 00 80 |
| 290 | GASKET | 001 | A 123 016 00 21 |
| 294 | SCREW Replaced by: N 000933 008337 |
- | N 000933 008116 |
| 294 | SCREW Replaced by: A 009 990 01 01 |
- | N 000933 008337 |
| 294 | SCREW | 003 | A 009 990 01 01 |
| 296 | SEALING RING | 003 | N 915035 000003 |
Copyright © 2024 WebAutoCat.com. All rights reserved. Terms of Use | Privacy Policy